Airsoft Micro Red Dot Mount on 4x32 Scope
Airsoft Micro Red Dot Mount on 4x32 Scope
Piggyback vs Offset optic mount, which one should you lot employ on your rifle?
In this commodity, we are going to break it down.
There are pros and cons of using them. No matter which configuration you choice, y'all accept to train with it to be skillful.
Piggyback Carmine Dot Mountain
Advantages
- Minimized lateral profile
- In line with bore
- Alpine mountain works for cross-centre dominant shooters
Disadvantages
- Lack cheek weld consistency
Angled First Ruby-red Dot Mount
3 Common Telescopic and Red Dot Setup Options
Choice 1 - Long-Range Setup, As well Short-Range Ready
For all you long-range DMR fans out in that location, you lot like having a heavy-duty, large profile long-range scope on your rifle for distance shooting.
In guild to brand your setup also close range capable without swapping optics, it's recommended to just add an angled offset red dot sight mount. Tilting the burglarize to the side would accept the red dot sight motion picture right in front of you. Some fifty-fifty use kickoff fe sights to co-witness with the RDS.
This type of setup is the easiest and fastest way to transition from magnified long-range scope to a 1X fixed optic.
Don't have a micro carmine dot even so? please check out this MRDS heir-apparent'south guide.
Notation: If you like to mountain an offset red dot optic on the scope ring adapter like the LaRue LT 137 J-Betoken or Spuhr, be certain to check the alignment to the bore.
Personally, I don't like starting time scope band adapter considering they don't usually align with the bore, which causes zeroing and holdover headaches. It also increases the vertical profile of the optic setup.
If you're non sure about how to properly null a offset sight delight read here.
Option 2 - Hybrid Crimson Dot Magnifier Setup
In contempo years, carmine dot sight magnifier combo setup has been super popular. The shooter can flip the magnifier to the side when transitioning back to 1X for shut-range targets.
The Aimpoint twist mount allows the shooter to quickly mount or demount the magnifier as needed, which is one of our favorites.
Recently, there are products on the market that let the shooter to tuck the magnifier down for minimized side contour, similar the new Scalarworks and Unity Tactical setup.
Selection 3 - 2 In 1 Optic Piggyback Setup
Sights like the ACOG, ELCAN, Leupold HAMR are made with Piggyback scarlet dot optic adapter. The optic sits right on meridian of the primary magnified optic.
The shooter just needs to shift his head up or down for transition.
What I like the best nigh this setup is that this is a 2 in 1 bundle, and the ii aiming reticles are all inline with the diameter.
That extra top gives the shooter who wears a helmet and other kits a fleck more than room to work with.
Note: What I don't like is when the shooter aim through the red dot sight, and then lifts up his head and no longer cheek welding the rifle for fast steady shots.
Piggyback vs. Commencement Holdover
Image Referenced MarineCorpsTimes
- Piggyback red dot sight sits but above your principal sight, and the line of sight sits a chip higher than the diameter. The point of aim and the betoken of touch on are more than aligned for long-altitude shots.
Still, at close range distance such as 10 to 25 yards, the shooter needs to learn a new holdover technique and zero
Piggyback setup is not recommended for high pinnacle over bore burglarize similar the Tavor X95 for CQB reasons.
- Angled offset mountain is my favorite because it sits low. All y'all have to do is tilt the rifle and appoint the target as you would with your primary optic.
In that location is no meaning beginning you need to recoup for. However, when aiming canted with the primary optic, in that location volition exist signal of impact shifts.
Red Dot Sight On Scope Ring Adapter (Angled)
This is my LEAST favorite configuration considering the optic sits way also high and they don't usually align with the bore.
If I have to pick a scope ring adapter I would pick on that sits directly on peak of the scope rather than at an bending.
I desire my red dot sight to be aligned with the bore without learning a new holdover.
FAQ
Which Scope Mounts Accepts Offset Telescopic Ring Adapter
LaRue LT137 and Sphur mounts have adapters you tin purchase to mount an offset optic. Some are made for piggyback and some are angled.
Other Recommended Dual Optics Setup
Leupold has made a very unique hybrid optic arrangement that combines the LCO and D-EVO together for shut-range and long-range.
The shooter can transition from the 1X to 6X back and forth by shifting merely their eyes mere 6 degrees.
- Without adjusting cheek weld
- Without magnification adjustment
- Without moving the shooter's head
Good News:The D-EVO is a standalone magnified optic with its own dedicated aiming reticle, and it can be pair with whatsoever other red dot sights as long every bit you're using lower 1/third co-witness mountain.
Epitome Referenced GunsandAmmo
Dual Optic Setup Tips
- Keep all optics marshal with the bore to avoid horizontal holdover
- Go along offsetting ruby dot sight equally low as possible to avoid meaning vertical holdover
- Place start angled mount favorable to your dominate side
- Do Non aught offset red dot sight at an angle
- Do Not use telescopic tube offset mount
Airsoft Micro Red Dot Mount on 4x32 Scope
Posted by: garciaheme1972.blogspot.com
0 Response to "Airsoft Micro Red Dot Mount on 4x32 Scope"
Post a Comment